Anchor coverall

Ankers Sweater - My Size is worked from the top down. The yoke consists of segments of rib followed by classic raglan increases. The sleeves are finished with double-pointed needles or Magic Loop technique. Anchor Sweater is assembly-free.Size guide and measurementsPlease note that you can only use the measurements in the pattern if the gauge is correct.Sizes XS (S) M (L) XL (2XL) 3XL correspond to chest measurements of approximately 80-85 (85-90) 90-95 (95-100) 100-110 (110-120) 120-130 cm. Anker's Jumper - My Size should have a room to move (positive ease) of approximately 6-10 cm. This means that if you measure 95 cm around your chest (measure yourself with a tape measure around your chest or the widest part of your body), you should knit a size M, which has an overall width of 102 cm.

Oslohuen - Christmas Edition is worked from the bottom up in stockinette stitch. The first part is worked on circular needles (40 cm), while the top is worked with double-pointed needles or Magic Loop technique.Size: 0-2 (2-4) 4-10 yearsGoals: Fits head circumference 48-50 (50-52) 52-55 cmKnitting tension: 23 stitches x 32 rows in stockinette stitch on a 3 mm needle = 10 x 10 cmGuiding sticks: 3 mm circular needle (40 cm), 3 mm double-pointed needles (or a long circular needle if you knit with Magic Loop technique)

The Storm Sweater is worked from the top down with textured knit. First the back is worked, shaped with short rows to form the shoulder slope. Then stitches are picked up for the shoulders, which are joined in front for the front. The front and back are joined under the armhole to form the body, which is worked straight down. The sleeves are worked in the round on double pointed needles or using the Magic Loop technique. A ribbed edge is worked at the neck, which is folded over and knitted down. The Storm Sweater is worked in a textured knit consisting of four different pattern segments.Make a swatch before you start to measure the gauge - note that the gauge must be correct in both height and width to match the measurements on the front. You can make a gauge swatch according to the diagram in the pattern.

The Wednesday Sweater is worked from the top down. First the upper back is worked back and forth, shaping the slope of the shoulders with short rows for a good fit. Then the shoulders are worked separately back and forth on circular needles. These are joined at the front to form the front. The front and back are then joined to form the body, which is worked in the round on circular needles. The sleeves are worked from picked up sts along the sleeve opening and worked in the round on circular needles and double-pointed needles or Magic Loop-technique. The large turtleneck of the neck is finally worked from picked up stitches and rib is worked with twisted stitches.Knit a test swatch to find the needle size that gives you the right gauge.Size guideWednesday Sweater should have a room to move (positive ease) of approximately 25 cm in relation to your chest measurement. The fit is oversize. Sizes XS (S) M (L) XL (2XL) 3XL (4XL) 5XL correspond to a chest measurement of 80-85 (85-90) 90-95 (95-100) 100-110 (110-120) 120-130 (130-140) 140-150 cm. The measurements of the finished sweater are given on the front of the pattern. Measure yourself before you start knitting to assess which size will fit you best. For example, if you measure 90 cm around your chest (or the widest part of your body), you should knit a size S. A size S sweater is a size S. S sweater has an overall width of 115 cm and in this example will give you a room to move (positive ease) of 25 cm.Sizes: XS (S) M (L) XL (2XL) 3XL (4XL) 5XLThe sweater's upper width: 110 (115) 120 (125) 135 (145) 155 (165) 175 cm (measured just below armhole)Length: 62 (63) 64 (65) 70 (72) 73 (74) 76 cm (measured centre back without turtleneck)Knitting tension: 15 stitches x 24 rows in stockinette stitch on a 5 mm needle = 10 x 10 cm after washing and blocking16-17 stitches x 24 rows in rib (k1 tbl, p1 tbl) on a 5 mm needle = 10 x 10 cm after washing and blocking (gauge for turtleneck and other rib edges)Guiding sticks: 5 mm circular needles (40, 60 and 80 and/or 100 cm), 5 mm double-pointed needles (unless knitting with Magic Loop-technology)